ANALISIS TEGANGAN STATIK STANDAR SAMPING SEPEDA MOTOR MATIC MENGGUNAKAN BAHAN STEEL ALLOY DENGAN SOFTWARE SOLIDWORK

Ratna Fajarwati Meditama; Diama Rizky Septiawan; Agus Dwi Putra; Bisyri Nur Wahid

doi:10.33474/rme.v4i2.22758

Authors

Ratna Fajarwati Meditama Universitas Islam Raden Rahmat Malang
Diama Rizky Septiawan Politeknik Negeri Malang
Agus Dwi Putra Politeknik Negeri Malang
Bisyri Nur Wahid Universitas Islam Raden Rahmat Malang

DOI:

https://doi.org/10.33474/rme.v4i2.22758

Keywords:

Stress analysis, side stand, motorcycle, Steel Alloy, finite element method, SolidWorks.

Abstract

This study presents a static stress analysis on the side stand of a matic motorcycle using Steel Alloy material, applying the finite element method and SolidWorks software. Motorcycles are a popular means of transportation, especially in rural areas where users often modify the side stand to support additional loads. The side stand is a critical component that allows the motorcycle to remain stable when parked. However, this component frequently encounters damage due to loads exceeding its initial design capacity. This research aims to evaluate the structural strength and safety factor of the side stand under a 2240 N load. Simulation results indicate that the maximum stress experienced remains below the yield strength of the Steel Alloy used. The obtained safety factor supports the material's application in side stand structures, provided that load limits are observed. This study is expected to contribute to the development of more load-resistant side stand designs, especially for rural usage needs.

References

A. D. Putra, Y. F. Pradani, and A. Saepuddin, MEKANIKA TEKNIK 1 (STATIKA STRUKTUR), vol. 1. 2022.

R. Danielis, L. Rotaris, M. Giansoldati, and M. Scorrano, “Drivers’ preferences for electric cars in Italy. Evidence from a country with limited but growing electric car uptake,” Transp. Res. Part A Policy Pract., vol. 137, no. October 2019, pp. 79–94, 2020, doi: 10.1016/j.tra.2020.04.004.

A. D. Putra, M. Rohman, and A. Wahab, “Analisis Desain Excavator Bucket Menggunakan Metode Elemen Hingga dengan Material Baja,” vol. 16, pp. 4–7, 2020.

A. D. Putra, Y. F. Pradani, and M. O. Al Momani, “Analisis material polimer ramah lingkungan berbahan rumput laut e-cottonii sebagai kandidat pengganti kemasan plastik,” Taman Vokasi, vol. 10, no. 2, pp. 137–148, 2022, doi: 10.30738/jtvok.v10i2.13274.

A. D. Putra and M. Rohman, “Analisis perancangan service special tools shock absorber dengan generator ac menggunakan finite element methods,” J. Taman Vokasi, vol. 9, no. 1, pp. 1–14, 2021, [Online]. Available: https://jurnal.ustjogja.ac.id/index.php/tamanvokasi/article/view/10231

A. D. Putra, D. I. Tsamroh, Y. F. Pradania, R. F. Meditama, and A. Muffliha, “Effect of Cathode Distance, Anode and Electroplating Time on Steel Alloy Corrosion Rate,” Transmisi, vol. 19, no. 1, pp. 49–55, 2023, doi: 10.26905/jtmt.v19i1.9650.

A. D. Putra, M. Rohman, and M. Sulaiman, “Simulasi Pengaruh Waktu dan Gerak Terhadap Desain Implan Sendi Pinggul,” J. Pendidik. Tek. Mesin Undiksha, vol. 09, no. 01, pp. 23–31, 2021, doi: http://dx.doi.org/10.23887/jptm.v9i1.28885.

A. D. Putra, B. C. Tjiptady, D. I. Tsamroh, Y. F. Pradani, and D. Hani, “Analisis Shaft Piston Rod Shock Absorber dengan Material Baja Karbon Menggunakan Finite Element Method,” vol. 15, no. 2, pp. 11–18, 2024.

A. D. Putra, Andoko, R. Wulandari, and G. A. Kurniawan, “Simulation of hip joint implants using finite element method with time and load variations,” Key Eng. Mater., vol. 851 KEM, pp. 111–121, 2020, doi: 10.4028/www.scientific.net/KEM.851.111.

A. D. Putra and Y. F. Pradani, “SIMULASI BATANG PENGHUBUNG PISTON DENGAN VARIASI MATERIAL Al Alloy DAN Ti Alloy MENGGUNAKAN METODE ELEMEN HINGGA,” J. Teknol. Terap. G-Tech, vol. 4, no. 1, pp. 279–285, 2020, doi: 10.33379/gtech.v4i1.545.

W. D. Callister and J. Wiley, Materials Science and Engineering. 2006.

X. Zhao et al., “Microstructure and mechanical properties of 304 stainless steel produced by interpass milling hybrid direct energy deposition-arc,” J. Mater. Res. Technol., vol. 27, no. October, pp. 3744–3756, 2023, doi: 10.1016/j.jmrt.2023.10.137.