Comparative Analysis of the Effects of Annealing, Normalizing, and Hardening Heat Treatments on the Characteristics of ST60 Steel

Dewi 'Izzatus Tsamroh; Warkoyo

doi:10.33474/rme.v6i1.25583

Authors

Dewi 'Izzatus Tsamroh University of Muhammadiyah Malang
Warkoyo University of Muhammadiyah Malang

DOI:

https://doi.org/10.33474/rme.v6i1.25583

Keywords:

ST60 Steel, Heat Treatment, Microstructure, Hardness

Abstract

ST60 steel is widely used in manufacturing applications, including components of agricultural machinery such as shafts, transmission elements, and structural parts that require adequate strength and durability. Heat treatment is a commonly applied process to modify the microstructure and mechanical properties of ST60 steel according to specific engineering requirements. This study aims to comparatively analyze the effects of annealing, normalizing, and hardening heat treatments on the hardness and microstructural characteristics of ST60 steel. The experimental procedure involved heating ST60 steel specimens to the austenitizing temperature, followed by different cooling methods corresponding to each heat treatment process. The treated specimens were subsequently evaluated through Rockwell hardness testing and optical microscopy observations. The results showed that heat treatment significantly influenced the hardness and microstructure of ST60 steel. The highest average hardness was obtained from the hardening process, reaching 87.4 HRC, due to the formation of a predominantly martensitic microstructure during rapid cooling. The normalizing process produced an average hardness of 53.9 HRC and was characterized by the formation of fine pearlite, providing a balance between strength and toughness. Meanwhile, the annealing process yielded the lowest average hardness of 29.5 HRC, associated with the development of coarse pearlite, which enhanced ductility and machinability. Microstructural analysis confirmed a strong relationship between cooling rate, phase transformation, and hardness variation. These findings demonstrate that the selection of an appropriate heat treatment method is crucial for tailoring the properties of ST60 steel to meet the performance requirements of agricultural machinery and other industrial applications.

References

D. Purwanto, “Analysis Of Charpy Method Impact Testing Using ST60 Steel Specimens Historical Perpectives And Current Trens,” Int. J. Mech. Eng., vol. 9, pp. 19–24, 2024, [Online]. Available: http://www.iaras.org/iaras/journals/ijme%0AThe.

D. I. Tsamroh, A. D. Putra, and J. Maulana, “Analisis Struktur Mikro pada Baja ST60 Hasil Perlakuan Hardening dengan Menggunakan Variasi Media Pendingin,” Ring Mech. Eng. ( RING ME ), vol. 4, no. 2, pp. 83–89, 2024.

A. Rahman, “Penggunaan Metode Fmeca (Failure Modes Effects Criticality Analysis) Dalam Identifikasi Titik Kritis Di Industri Kemasan,” J. Teknol. Ind. Pertan., vol. 31, no. 1, pp. 110–119, 2021, doi: 10.24961/j.tek.ind.pert.2021.31.1.110.

A. Susanto, D. A. Wicaksono, B. Asngali, N. N. Wahyudi, and R. E. Wicaknono, “Aplikasi Teknik Manufaktur untuk Perawatan dan Reparasi Kerusakan Peralatan Pertanian Jenis Mesin Perontok Padi,” J-ADIMAS (Jurnal Pengabdi. Kpd. Masyarakat), vol. 10, no. 2, pp. 70–74, 2022.

F. R. P. Hantoro, E. Prasetyo, and A. Hermawan, “Dampak Penggunaan Alat dan Mesin Pertanian terhadap Produksi Padi di Kabupaten Tegal,” Pangan, vol. 29, no. 3, pp. 171–180, 2020.

Pramuko Ilmu Purboputro, Sartono Putro, and Djoeli Satrijo, “The analysis of carburizing with15, 30, 40,45,60 minutes holding time due to hardness and microstructure on ST 60 Steel,” JTTM J. Terap. Tek. Mesin, vol. 4, no. 1, pp. 55–63, 2023, doi: 10.37373/jttm.v4i1.448.

A. Widyanugraha, A. Santosa, D. T. Santoso, T. Mesin, F. Teknik, and S. Karawang, “Perancangan Mesin Penggiling Padi dan Penepung Sekam Padi Skala Rumah Tangga,” J. Tek. Mesin, vol. 13, no. 2, pp. 69–75, 2020, [Online]. Available: http://ejournal2.pnp.ac.id/index.php/jtm.

G. Priyotomo, I. N. G. P. Astawa, and F. Rokhmanto, “The Effect of Heat Treatment on Mechanical Properties of J4 Series Stainless Steel Metals,” Teknik, vol. 42, no. 2, pp. 117–122, 2021, doi: 10.14710/teknik.v42i2.36461.

D. I. Tsamroh and M. Riza Fauzy, “Peningkatan Sifat Mekanik Al6061 Melalui Heat Treatment Natural-Artificial Aging,” G-Tech J. Teknol. Terap., vol. 6, no. 1, pp. 8–13, 2022, doi: 10.33379/gtech.v6i1.1217.

Y. M. Wang et al., “Study on the role of cryogenic treatment on corrosion and wear behaviors of high manganese austenitic steel,” J. Mater. Res. Technol., vol. 24, pp. 5271–5285, 2023, doi: 10.1016/j.jmrt.2023.04.100.

S. Noh et al., “Effects of heat treatments on microstructures and mechanical properties of dual phase ODS steels for high temperature strength,” Nucl. Eng. Technol., vol. 45, no. 6, pp. 821–826, 2013, doi: 10.5516/NET.02.2013.529.

S. Leal and S. Ferreira, “Heat treatment of the SAE 9254 spring steel : Influence of cooling rate on the microstructure and microhardness,” Next Mater., vol. 3, no. September 2023, p. 100175, 2024, doi: 10.1016/j.nxmate.2024.100175.

Y. Zhang, W. Liu, X. Long, Z. Liu, Y. Li, and Z. Yang, “Combining in-situ technology to study the influence of bainite morphology on the strength and toughness properties of medium-carbon bainitic steel,” J. Mater. Res. Technol., vol. 36, no. February, pp. 34–44, 2025, doi: 10.1016/j.jmrt.2025.03.106.

B. Li et al., “Revealing the microstructural evolution and strengthening mechanism of Mg-5.5Gd-3Y-1Zn-0.5Mn alloy in centrifugal casting and subsequent hot rolling,” J. Alloys Compd., vol. 984, no. February, p. 173950, 2024, doi: 10.1016/j.jallcom.2024.173950.

A. Kešner, R. Chotěborský, M. Linda, M. Hromasová, E. Katinas, and H. Sutanto, “Stress distribution on a soil tillage machine frame segment with a chisel shank simulated using discrete element and finite element methods and validate by experiment,” Biosyst. Eng., vol. 209, pp. 125–138, 2021, doi: 10.1016/j.biosystemseng.2021.06.012.

Z. Ma et al., “Microstructural evolution and enhanced mechanical properties of Mg–Gd–Y–Zn–Zr alloy via centrifugal casting, ring-rolling and aging,” J. Magnes. Alloy., vol. 10, no. 1, pp. 119–128, 2022, doi: 10.1016/j.jma.2020.11.009.

D. I. Tsamroh, A. D. Putra, D. Puspitasari, C. Yazirin, and M. I. N. Sasongko, “Analisis Kekuatan Rangka Mesin Penggiling Padi Berbahan ASTM A500 Menggunakan Simulasi FEM,” Ring Mech. Eng. (RING ME), vol. 5, no. 1, pp. 1–12, 2025.

R. Nishio, T. Umetani, Y. Nakamura, T. T. Sasaki, and A. Shibata, “Materials Science & Engineering A Effect of cooling rate after high-temperature heating on the ductility of 19Cr-0 . 020C-0 . 015N-0 . 4Nb stabilized ferritic stainless cast steel,” Mater. Sci. Eng. A, vol. 945, no. May, p. 148952, 2025, doi: 10.1016/j.msea.2025.148952.

F. Khosravi Maleki, M. KM Nasution, M. S. Gok, and V. Arab Maleki, “An experimental investigation on mechanical properties of Fe2O3 microparticles reinforced polypropylene,” J. Mater. Res. Technol., vol. 16, pp. 229–237, 2022, doi: 10.1016/j.jmrt.2021.11.104.

S. Gradesst, “Datasheet for Steel Grades Carbon Steel St60-2 St60-2 Standard Number : St60-2 Chemical composition ( mass fraction )( wt .%) St60-2 Physical Properties St60-2 Mechanical Properties St60-2 Heat Treatment Regime St60-2 Range of products We can produce Carbon Steel the specifications follows :,” pp. 1–2.

H. Hidayat, M. Jufriyanto, A. Wasiur Rizqi, A. Hesthi Permata Ningtyas, and R. M. Yusron, “Analysis of Load Variations on ST 60 Steel Using Vickers Method,” Int. J. Sci. Eng. Inf. Technol., vol. 05, no. 02, pp. 5–9, 2020.

A. K. L. Wujakshana, S. Sinarep, and I. Okariawan, “Pengaruh Proses Perlakuan Panas Plat Strip Stainless Steel AISI 304 dengan Media Pendingin Air Pohon Pisang, Air Garam, dan Air Terhadap Uji Kekerasan Vikers, Uji Impact, dan Struktur Mikro,” Universitas Mataram, 2021.

H. Zhu et al., “Effects of Ni and Al on microstructural evolution and mechanical properties in secondary hardening steels,” J. Mater. Res. Technol., vol. 39, no. September, pp. 1638–1652, 2025, doi: 10.1016/j.jmrt.2025.09.204.

J. Li et al., “Effects of deep cryogenic treatment on the microstructure evolution, mechanical and thermal fatigue properties of H13 hot work die steel,” J. Mater. Res. Technol., vol. 27, no. November, pp. 8100–8118, 2023, doi: 10.1016/j.jmrt.2023.11.236.

B. Andersson, E. Steyn, and J. Ahlström, “Materials & Design Thermal pulses on pearlitic steels : Influence of laser heat scanning parameters on surface layers transforming to martensite,” Mater. Des., vol. 256, no. April, p. 114199, 2025, doi: 10.1016/j.matdes.2025.114199.

A. Dermawan, Mustaqim, and F. Sidiq, “Pengaruh Temperatur Carburizing Pada Proses Pack Carburizing Terhadap Sifat – Sifat Mekanis Baja S 21 C,” Engineering, vol. 14, no. 1, pp. 7–14, 2017, [Online]. Available: http://e-journal.upstegal.ac.id/index.php/eng/article/view/738.

N. Koga, T. Nameki, O. Umezawa, V. Tschan, and K. P. Weiss, “Tensile properties and deformation behavior of ferrite and austenite duplex stainless steel at cryogenic temperatures,” Mater. Sci. Eng. A, vol. 801, no. August 2020, p. 140442, 2021, doi: 10.1016/j.msea.2020.140442.

L. M. Rymer, L. Winter, K. Hockauf, and T. Lampke, “Artificial aging time influencing the crack propagation behavior of the aluminum alloy 6060 processed by equal channel angular pressing,” Mater. Sci. Eng. A, vol. 811, p. 141039, Apr. 2021, doi: 10.1016/J.MSEA.2021.141039.

Q. Yu, Y. Zhao, and F. Zhao, “Materials Letters : X Effect of austenitizing temperature on microstructure and mechanical properties of medium carbon spring steel,” Mater. Lett. X, vol. 26, no. July, p. 100251, 2025, doi: 10.1016/j.mlblux.2025.100251.